Thermon TraceNet TCM 18 Bedienungsanleitung Seite 86
- Seite / 96
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
The TCM18 control module using foundation temperature sensing RTD’s in each
heating zone can be typically set at the control settings given below:
Control Parameter Setting
Controller Configuration Single RTD Input
Control Method Proportional
100% Power On Temperature 50
◦
F (10
◦
C)
Control Band 30
◦
F (17
◦
C)
High Alarm Temperature 90
◦
F (32
◦
C)
High Temp Trip On
Low Alarm Temperature 38
◦
F (3
◦
C)
In a proportional control mode, the heater should be continually operating using cy-
cle omission techniques in a warming mode (and will thus minimize condensation
within the heating system conduits). After attaining 50
◦
F (10
◦
C), the TCM18 will lin-
early reduce power until an equilibrium value between 50
◦
F(10
◦
C), and 80
◦
F(27
◦
C),
is obtained. In the unlikely event that the 80
◦
F (27
◦
C), setting is exceeded, the con-
trol will de-energize the heater circuit. A high temperature alarm will activate should
the RTD sensor detect a temperature above the 90
◦
F (32
◦
C) value and the circuit
will trip.
Having set in these values as well as the appropriate other limit/control values, the
following typical control can be achieved.
PN 50316_0514 82
- TraceNet™ TC 1
- Series Control System 1
- Maintenance Guide 2
- Contents 3
- 1 Introduction 5
- PN 50316_0514 2 6
- 2 Specifications 7
- 5 PN 50316_0514 9
- 3 Module Connections 11
- PN 50316_0514 8 12
- The RTB6 Module Connections 13
- The PM6 Connections 14
- The RM6 Connections 15
- 4 Field and Panel Wiring 16
- 13 PN 50316_0514 17
- Figure 6: RTD Sensor Location 17
- TraceNet Panel Wiring 18
- Serial Communication Wiring 18
- PN 50316_0514 19
- 5 Monitoring Heat 20
- 17 PN 50316_0514 21
- PN 50316_0514 18 22
- 19 PN 50316_0514 23
- PN 50316_0514 20 24
- 21 PN 50316_0514 25
- 6 Accessing Heat Tracing 26
- Figure 12: TCM18 LCD Response 27
- 23 PN 50316_0514 27
- PN 50316_0514 24 28
- 25 PN 50316_0514 29
- (1, 2, 3, 4, 5) 30
- PN 50316_0514 26 30
- 7 Programming the 31
- PROGRAM MODE ENABLED 32
- SELECT FUNCTION KEY 32
- Press the MAINTAIN TEMP key 32
- Figure 15: MAINTAIN TEMP Key 33
- 29 PN 50316_0514 33
- Figure 17: Programming Keys 34
- Figure 19: The ENTER Key 35
- 31 PN 50316_0514 35
- Figure 21: The PROG Key 36
- 33 PN 50316_0514 37
- PN 50316_0514 34 38
- 35 PN 50316_0514 39
- PN 50316_0514 36 40
- 37 PN 50316_0514 41
- PN 50316_0514 38 42
- 39 PN 50316_0514 43
- PN 50316_0514 40 44
- 41 PN 50316_0514 45
- PN 50316_0514 42 46
- 43 PN 50316_0514 47
- PN 50316_0514 44 48
- 45 PN 50316_0514 49
- 8 Heat Trace Control and 50
- 47 PN 50316_0514 51
- 9 The TCM18 in 52
- Figure 24: Heater Setup 53
- 49 PN 50316_0514 53
- Figure 25: Select RTD Setup 54
- 10 The TCM18 in 55
- PN 50316_0514 52 56
- 11 The TCM18 Data 57
- 12 System Start-Up 58
- 13 Maintenance 59
- PN 50316_0514 56 60
- 57 PN 50316_0514 61
- Wiring and Connections Survey 62
- 59 PN 50316_0514 63
- 14 Notes 64
- 61 PN 50316_0514 65
- 15 More Information 66
- Appendix A 67
- Trouble Shooting Tips 67
- PN 50316_0514 64 68
- Low Temperature Reading/Alarm 69
- PN 50316_0514 66 70
- 67 PN 50316_0514 71
- RTD Sensor Alarm 72
- Communications Alarm 72
- Circuit Fault Alarm 73
- High Current Readings/Alarms 73
- PN 50316_0514 70 74
- Low Current Readings/Alarms 75
- PN 50316_0514 72 76
- High Ground Current Alarm 77
- PN 50316_0514 74 78
- Appendix B Temperature and 79
- Current Limits 79
- PN 50316_0514 76 80
- Appendix C 81
- Advanced Features of the 81
- TCM18 Ambient Control 81
- PN 50316_0514 78 82
- 79 PN 50316_0514 83
- Appendix D Typical TCM18 84
- Control Applications 84
- 81 PN 50316_0514 85
- 83 PN 50316_0514 87
- 85 PN 50316_0514 89
- PIPE TEMPERATURE 90
- DEGREES CELSIUS 90
- 87 PN 50316_0514 91
- 89 PN 50316_0514 93
- Appendix E Utilities 94
- Appendix F Markings for 95
- Explosive Atmospheres) 95
- Thermon Manufacturing Company 96
- 100 Thermon Drive 96
- San Marcos Texas 96
- Thermon PN 50316_0514 96
Verwandte Produkte und Handbücher für Hardware Thermon TraceNet TCM 18
Hardware Thermon ET-6C Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Hardware Thermon TBX-3LC Bedienungsanleitung
(5 Seiten)
(5 Seiten)
Hardware Thermon ET-7C Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Hardware Thermon FAK-7 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Hardware Thermon FAK-9 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Hardware Thermon FAK-1 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Hardware Thermon FAK-2 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Hardware Thermon FAK-4 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Hardware Thermon FAK-5 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Hardware Thermon FAK-8 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Hardware Thermon KSR Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Hardware Thermon KSR-EJK Bedienungsanleitung
(3 Seiten)
(3 Seiten)
Hardware Thermon KSR-CFK Bedienungsanleitung
(5 Seiten)
(5 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.171 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern